how to install fluorescent lighting

Download Article

Changing a standard incandescent light bulb is, of course, the simplest of tasks. However, you may find yourself pausing when it comes time to replace a long, tube-style fluorescent lamp that is not immediately obvious how the bulb is removed from the housing. While it may seem intimidating, replacing fluorescent lighting can be simple.

1

Make sure that the power is switched off. Before replacing a fluorescent light, you should make sure the fixture is not powered on. Do not simply use the wall switch to remove power to the fixture. You can use the fuse box to shut off power to the lamp's circuit. Use a voltage tester to verify that there is no power in the fixture.^[1]
2

Prepare a stepladder or other support. Most likely, you will not be able to reach the fluorescent light fixture comfortably from ground level. Position a stepladder underneath the fixture to replace the lamps comfortably and safely.^[2]

Advertisement
3

Rotate the first tube 90 degrees. Reach up, and gently support the first fluorescent tube with both hands, keeping your hands as close to the ends of the bulb as possible. You will be able to rotate the tube in either direction a quarter-turn until it stops. This action rotates the prongs, that project from each end of the bulb, to a vertical alignment, and so allows you to slide the tube downward and out of the fixture.
4

Gently lower the fluorescent tube straight down through the slot. Place the tube gently out of the way, where it cannot roll or be disturbed.
5
Lift the new fluorescent tube into place. To install the new light, line its prongs up with the slots in either socket. Push the tube straight up into the sockets, and then rotate it 90 degrees until you feel it lock into place. You can give the lamp a gentle tug to ensure that it is firmly in place.^[3]
- Consider installing LED lighting instead, which uses less energy, lasts longer, and produces a more natural light.
6

Repeat this process with the other lamp. Most often, fluorescent light fixtures are designed with two tubes side-by-side. The process for replacing each tube is the same.^[4]
7

Test the new bulb. Flip the fuse box switch back on, then flip your wall switch on. See if the new fluorescent bulbs light up properly, noting that fluorescent lamps take a minute or so to reach full brightness. If the new bulbs do not work properly, you may have a defective component in your light fixture that needs to be replaced.^[5]

Advertisement

1

Change out cracked sockets. Cracked sockets are often caused by other objects bumping into the fixture, or too much stress while removing a bulb. First, turn off the power to the light, and remove the bulbs. Keep the wiring order straight as you take out the old socket. It is important to cut only one wire lose at a time. Strip each wire back by 1/2 in., and put the stripped wire end into the terminal slots of the new socket. Do this for each wire.^[6]
2
Inspect the ballast. The ballast controls the amount of incoming voltage that start the light tubes. It also regulates the electricity to give constant light. If you believe that the ballast needs replacement, you may want to consider purchasing a whole new fixture. Ballast replacement may cost the same amount as a new fixture.^[7]
- A humming sound produced by your fluorescent light fixture usually indicates that the ballast, rather than the bulbs, needs to be replaced.
3
Check the fuse box for flickering lights. The bulb may not be getting enough power. Try resetting the fuse box by flipping the power switch off and on.^[8]
- If the bulb is still flickering, try replacing the bulb.^[9]
Advertisement

1

Check for light frames. Office lighting is usually behind a bezel lens with a frame. These types of recessed fixtures are holding the light tubes in place to minimize accidents and breakage. They can be very frustrating due to the lack of wiggle room or freedom of movement. The frame is held in place by lever locks or snaps that you have to take out.
2

Remove the cover. First, use a screwdriver to pry down the levers, while supporting the frame in the middle. It is important to support the frame because it can ruin the locks or swing down and hit you in the head.^[10]
3

Clean the fixture. Take the opportunity, while the lens is down, to remove insects, dust, condensation or mold from the lens surface.
4
Take out the bulb. Depending on the bulb, you will either need to twist, or unsnap, each end of the fluorescent tube. Be sure to only do one end at a time to maintain more control over the bulb.^[11] Once you wiggle the first tube out, the other tubes will come out much more easily.^[12]
- Search for holes, or a recessed area, that the cathode/anode pin can sink into that permit freedom of movement.
5

Lock in the new bulbs. To install the new light, line its prongs up with the slots in either socket. Push the tube straight up into the sockets, and then rotate it 90 degrees until you feel it lock into place. You can give the lamp a gentle tug to ensure that it is firmly in place.^[13]
6
Finish the job. When the last tube is in, swing the lens frame back in. Use both hands to support the frame in place. Then, use your thumbs to swing the frame lock back in.
- Snap locks may need to be pressed firmly to snap back in.^[14]
Advertisement

Add New Question

Question

How do you remove a fluorescent light?

Daniel Stoescu is a Master Electrician and the Owner and Operator of Home Tech Solutions, LLC in Hampton, Virginia. With over a decade of experience, Daniel specializes in wiring residential, commercial, and light industrial structures. The Home Tech Solutions team has over four decades of combined experience and offers comprehensive solutions for residential electrical needs.

Master Electrician

Expert Answer

Turn the power off and apply downward pressure at the end of the bulb. Keep in mind that circular fluorescent bulbs may shatter easily.
Question

What is a fluorescent starter?

This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.

wikiHow Staff Editor

Staff Answer

A fluorescent starter is a timed switch. It lets the current flow through the filaments, which are located at each end of the fluorescent light tube.
Question

How do you change a light ballast?

This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.

wikiHow Staff Editor

Staff Answer

Changing a light ballast is an involved process, so it's important to follow step-by-step instructions that explains exactly what to do. Be sure the replacement used is of the same technology. It is suggested that you read all of this wikihow: How to Replace the Ballast in a Fluorescent Lighting Fixture, including its warnings, so you know what to do correctly.
Question

Can you replace fluorescent lights with track lighting?

This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.

wikiHow Staff Editor

Staff Answer

Yes, you can replace fluorescent lights with track lighting and fortunately, you can use the same wiring so you won't need to replace existing wiring unless it's in poor condition. You'll only need one connection for track lighting. Make sure you turn off the electricity before removing and changing the lights and only do it yourself if you're comfortable with electrical DIY work, otherwise get some qualified help.
Question

If a fixture is using 32 watt bulbs, can I use 40 watt bulbs instead?

The general rule of thumb is to not exceed the recommended wattage. If the appliance says that you can only use bulbs that are 32 watt or less, then you need to stick with that. However, if it says you can use higher wattage, then that would be okay. Without knowing what your appliance actually specifies, that's the best advice that can be provided.
Question

Is it possible to change it to an LED bulb with the same fixture?

Lana Vanlandingham

Community Answer

There are some LED bulbs that work in fluorescent fixtures. Check your warehouse and home improvement stores.
Question

How do I discard a fluorescent tube?

Take it to the store that sold you the new bulbs and ask if they will properly recycle it to keep the mercury away from people and animals eaten by people. If not, wait for a day with hazardous waste recyling, but be careful not to let the bulb be broken.
Question

What can cause 2 lights to work and 2 lights not to work?

Check for loose wires and try to reset the fuse. If it still doesn't work, you will need a replacement fixture.
Question

Although not shown in the video, is it necessary to wear gloves for this type of light bulb?

Not unless you feel safer doing so. Just avoid being rough with the bulb, or else you may break it and spill harmful chemicals everywhere.
Question

How do I remove broken glass from a fluorescent bulb from my skin?

Go to hospital! Fluorescent bulbs have chemicals inside so you need to see a doctor.

Show more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Unlike incandescent bulbs, fluorescent bulbs rarely burn out completely. Instead, they dim or begin flickering over time, indicating that they need to be replaced.

Broken light bulbs pose a risk of eye and skin injury. Wearing safety glasses when replacing a bulb will help reduce the risk of eye injury in case of a breakage.
Fluorescent bulbs of all types contain a small amount of mercury, which means they pose a health risk if broken. If you break a fluorescent bulb, open a window for ventilation and sweep the broken pieces into a container you can reseal for disposal.

Things You'll Need

Stepladder
Fluorescent bulbs
Safety glasses

About This Article

Article SummaryX

To replace fluorescent lighting, locate the fuse box and shut off the power. If the light is overhead, position a sturdy stepladder underneath the fixture, then reach up and support the tube with one hand while you rotate it 90 degrees with your other hand. Next, slide the tube out of the fixture and put the tube aside. Lift the new fluorescent tube into place and line its prongs up with the slot on each end of the socket. Push the tube straight up into the sockets and rotate it 90 degrees until you feel it lock into place. If you want to learn how to remove frames covering your lights, keep reading the article!

Did this summary help you?

Thanks to all authors for creating a page that has been read 520,178 times.

Did this article help you?